Alcor+mp+200717+install [top] -

AlcorMP 20.07.17 is a specific version of a Mass Production (MP) tool used to repair or reflash USB flash drives that use Alcor Micro

controllers (such as the AU6989SN-GT). These tools are typically used when a drive becomes "Write Protected," shows "No Media," or has a capacity of "0 bytes". Installation and Setup Guide Identify the Controller : Before running the tool, use a diagnostic utility like ChipGenius

to confirm your USB drive uses an Alcor Micro controller. Each flash drive requires a specific tool version based on its controller part number and Flash ID. Download and Unzip

: Download the AlcorMP 20.07.17 package. Most official sources provide these as password-protected ZIP files; you must unzip the files to a local folder before executing the binaries. Run as Administrator : Right-click the executable (often named AlcorMP.exe

) and select "Run as Administrator" to ensure it has the necessary permissions to access hardware drivers. Connect the Drive

: Plug in the corrupted USB drive. The tool should detect it automatically in one of the status slots. Using the Tool for Repair Configure Settings : Click on the

button. You may need to leave the password field blank or enter a default (commonly Flash Management

: The tool allows you to configure firmware settings to address corrupted firmware or set aside "bad blocks" on the NAND memory. Start the Process to begin the low-level format or reflash. This process will erase all data on the NAND chip. Completion

: Once the status turns green or shows "OK," the drive will typically be partitioned into a smaller, accessible volume, bypassing the original corruption. alcor+mp+200717+install

: Using the wrong MPTool version or incorrect settings can permanently damage (brick) your USB hardware. Always verify your matches the tool's supported list. tool to verify your controller's

The phrase "alcor+mp+200717+install" refers to the installation process for a specific 2020 version of the Alcor Micro USB Production Tool (MP Tool). This specialized software is used by technicians and enthusiasts to "revive" corrupted USB flash drives, reflash firmware, or fix "Disk is Write Protected" errors on devices using Alcor controllers.

Here is a short story about a high-stakes repair using this exact tool. The Ghost in the Drive

Silas stared at the small, silver USB stick sitting on his desk like a dead robotic beetle. It held the only copy of his thesis, but Windows was adamant: “The disk is write-protected.” It wouldn't format. It wouldn't open. It was a digital brick.

He spent four hours in the dark corners of hardware forums until he found a lead. He peeled back the metal casing of the drive with a pocketknife, squinting at the tiny black chip inside. "Alcor Micro," he whispered.

He didn't need a file recovery program; he needed a resurrection. He searched for the specific ritual: Alcor MP 200717.

The download was a cryptic .7z file from a site that looked like it hadn't been updated since 1998. After extracting it, he found the executable. He right-clicked and selected "Run as Administrator."

The interface was industrial—all grey boxes and technical parameters. He plugged the dead drive in. A single square in the grid turned yellow. [G:] AU6989SN-GT AlcorMP 20

This was the moment of no return. Using the 200717 install version, he opened the Setup menu. He didn't want a "High Level Format"; he needed the "Low Level" deep-clean to bypass the controller's errors. He toggled the "Optimized" setting to Capacity and hit Start.

AlcorMP 20.07.17 is a specialized firmware flashing and mass production tool (MPTool) used primarily for repairing corrupted USB flash drives equipped with Alcor Micro controllers. Prerequisites & Safety Warnings : This process performs a low-level format and will permanently erase all data on the USB drive. Driver Warning : During operation, the tool installs a temporary driver ( mpszfilt.sys

). If the program crashes or is closed incorrectly, this driver may stay active and disable other USB devices like your keyboard or mouse. If this happens, reopen and close the tool correctly to uninstall the driver. Compatibility

: Ensure your drive uses an Alcor Micro chip (e.g., AU698x series) using a tool like ChipGenius before proceeding. Installation & Execution Steps Download and Extract : Obtain the version from a reputable source like Alcor Infotech . Extract the file to a dedicated folder on your desktop. Run as Administrator : Right-click AlcorMP.exe and select Run as Administrator Select Mode : If prompted upon startup, choose between (for basic repair/bad block scanning) or (for standard production/formatting). Connect Device

: Plug your corrupted USB drive into a direct motherboard port (avoid USB hubs). The tool should automatically detect it in one of the numbered slots. Configuration (Setup) . The default password is often blank or Flash Type tab, ensure "Auto Detect" is checked.

tab, verify the VID and PID match your chip's specifications (usually Start Flashing

to begin the firmware reinstallation. The status bar will turn green once the "OK" message appears. Common Troubleshooting Tool doesn't see USB : Try a different USB port or restart the software. Write Protection

: This tool is frequently used to fix "The disk is write protected" errors by overwriting the corrupted firmware flags. Error Codes : If you see codes like Introduction: Decoding the Alcor MP 200717 In the

, it often indicates a hardware failure or an incorrect firmware version selection. USB controller's part number to confirm this is the right version for your hardware?

Based on the keywords provided, this request refers to the installation of the Alcor Micro MP (Mass Production) Tool, specifically the version labeled v200717 (likely released on July 17, 2020, or a variant build).

This tool is widely used to repair corrupted USB flash drives or to partition USB sticks into CD-ROM partitions using Alcor Micro controller chips (AU6989, AU6998, SC908, etc.).

Here is a comprehensive article/guide on how to install and use the Alcor MP Tool v200717.

Introduction: Decoding the Alcor MP 200717

In the world of USB mass storage controllers, few names are as ubiquitous yet as cryptic as Alcor Micro. For technicians specializing in flash drive recovery, low-level formatting, or PID/VID customization, the string "alcor+mp+200717+install" represents a specific, critical junction. This combination of keywords points directly to a particular firmware version (200717) of the Alcor MP (Mass Production) tool.

If you are staring at a bricked USB drive, dealing with a “Write Protect” error that won’t go away, or trying to resurrect an old 2.0 or 3.0 flash drive, you have likely landed here. This article will walk you through the exact installation process, driver configuration, and operational nuances of the Alcor MP tool dated 200717.

What this guide covers:

  • Identifying if your USB drive uses an Alcor controller
  • Safe extraction and installation of the MP tool v200717
  • Driver signing bypass (Windows 10/11)
  • Step-by-step low-level formatting and firmware flashing
  • Common error codes and their fixes

Understanding Alcor

Alcor is a tool or software that might be used in various domains such as data processing, cloud management, or even game development, depending on the context. For this example, let's assume Alcor is a piece of software that requires installation and possibly integration with other systems or tools (like MP).

8. Final Notes & Safety

  • Never interrupt a firmware update or low-level format – it can permanently kill the controller.
  • AlcorMP 200717 does not support USB 3.0 drives or drives >64 GB (will hang).
  • Keep a backup copy of AlcorMP.ini – corruption of this file mid-flash can cause drive to be unrecognized.
  • If the drive becomes completely dead (no LED, not even detected), you may need to short two data pins (D+ and D-) or use a “recovery” version of AlcorMP (e.g., AlcorMP_200701).

Step 1: Download the Correct Driver

Search for Alcor Micro Smart Card Reader Driver 200717 from a trusted source (e.g., your device manufacturer’s support page, or official Alcor Micro partner site).
The package typically includes:

  • au9540_x64.msi (64-bit)
  • au9540_x86.msi (32-bit)
  • *.inf, *.sys, *.cat files

Do not use generic “driver updater” tools – they often break smart card functionality.

Scroll to Top