-rev B- - Ccna-2v7.0 Case Study

CCNA-2 v7.0 Case Study (Revision B) is a comprehensive capstone project within the Switching, Routing, and Wireless Essentials (SRWE)

course. This particular scenario typically revolves around the Carl I. Samson Company (C.I.S. Co)

, a firm based in Bangor, Maine, that has recently acquired a corporation with branch offices in Phoenix, AZ, and Chicago, IL.

The objective is to design, implement, and secure a multi-site network using a combination of IPv4 and IPv6

static routing until a permanent dynamic routing solution is decided. Core Phases of the Revision B Case Study

The project is generally divided into distinct phases that test your ability to build a functional and secure enterprise network. 1. IP Addressing and VLAN Design

You are tasked with creating a logical addressing scheme to support the different branches. VLAN Implementation

: Configuring multiple VLANs to segment traffic between departments (e.g., Management, Sales, Guest). Subnetting

: Applying IPv4 VLSM and IPv6 prefix assignments to maximize address efficiency. Inter-VLAN Routing Router-on-a-Stick

or Layer 3 switch configurations to enable communication between these segments. 2. Basic Device Configuration & Security

Before advanced features are added, you must harden each network device: Initial Settings

: Setting hostnames, encrypting all plain-text passwords, and configuring a "Banner Motd" to warn unauthorized users. SSH Access : Disabling insecure Telnet and configuring SSH Version 2 with a local username (e.g., ) and a 1024-bit RSA key for remote management. Login Security

: Implementing "block-for" commands to prevent brute-force attacks (e.g., disabling login for 1 minute after 3 failed attempts within 60 seconds). 3. Advanced Switching and Routing

This phase focuses on redundancy and reaching remote networks:

CCNA 2 v7.0 Case Study - Rev B: A Comprehensive Guide

Are you a student or a networking enthusiast preparing for the CCNA 2 v7.0 exam? If so, you're likely familiar with the case study - Rev B. In this post, we'll provide an overview of the case study, its objectives, and a step-by-step guide to help you complete it successfully.

What is CCNA 2 v7.0 Case Study - Rev B?

The CCNA 2 v7.0 case study - Rev B is a hands-on activity designed to assess your skills and knowledge in configuring and troubleshooting a small network. The case study is part of the Cisco Certified Network Associate (CCNA) curriculum, which focuses on developing practical skills in network configuration, management, and troubleshooting.

Objectives of CCNA 2 v7.0 Case Study - Rev B:

The objectives of the case study are:

Design and implement a small network
Configure network devices, including routers, switches, and PCs
Troubleshoot common network issues
Apply knowledge of network protocols, including OSPF, EIGRP, and VLANs

Step-by-Step Guide to CCNA 2 v7.0 Case Study - Rev B:

Here's a step-by-step guide to help you complete the case study:

Step 1: Understand the Network Topology

Study the given network topology and identify the devices, including routers, switches, and PCs.
Take note of the IP addresses, subnet masks, and default gateways.

Step 2: Configure Network Devices

Configure the routers, switches, and PCs according to the given requirements.
Use commands such as configure terminal, interface, ip address, and exit to configure the devices.

Step 3: Implement Network Services

Implement network services, including DHCP, DNS, and HTTP.
Use commands such as ip dhcp pool and ip name-server to configure these services.

Step 4: Troubleshoot Network Issues

Identify and troubleshoot common network issues, such as connectivity problems and routing issues.
Use commands such as show ip interface brief and debug ip ospf to troubleshoot the issues.

Step 5: Verify and Document

Verify that all network services are working as expected.
Document your configuration and troubleshooting steps.

Tips and Best Practices:

Read the case study requirements carefully and understand the network topology.
Use online resources, such as Cisco documentation and YouTube tutorials, to help you with configuration and troubleshooting.
Practice, practice, practice! The more you practice, the more confident you'll become in configuring and troubleshooting networks.

By following these steps and tips, you'll be well on your way to completing the CCNA 2 v7.0 case study - Rev B successfully. Good luck!

The CCNA 2 v7.0 (Switching, Routing, and Wireless Essentials) curriculum focuses on the architecture, components, and operations of routers and switches in small networks. Developing a case study for this specific version typically involves a scenario where a business must expand its network infrastructure to support multiple LANs and secure wireless access. Scenario Overview

You are a network administrator for a company called "E-MAGINE". The company is merging with another entity and expanding to a Wide Area Network (WAN) with multiple locations. Your goal is to design and implement a network that ensures inter-VLAN communication, secure access, and efficient routing. Core Case Study Components

A standard "Rev B" (Revision B) case study for CCNA 2 v7.0 should include the following modules: 1. VLAN and Inter-VLAN Routing

Objective: Segment the network for different departments (e.g., Sales, HR, IT). Requirements: Assign specific VLAN IDs and names (e.g., VLAN 10 - Sales). Configure 802.1Q trunking between switches.

Implement Router-on-a-Stick or Layer 3 Switching for Inter-VLAN routing. 2. Redundancy and STP Objective: Prevent loops in a multi-switch environment. Requirements:

Configure Spanning Tree Protocol (STP) to ensure a single loop-free path.

Optimize STP by designating a Root Bridge for specific VLANs.

Configure EtherChannel (Link Aggregation) to increase bandwidth and provide redundancy between switches. 3. Routing Concepts and Configuration Courses and training - PJATK GDAŃSK

CCNA-2 v7.0 Case Study (Rev B) focuses on the "Switching, Routing, and Wireless Essentials" (SRWE) curriculum. It typically centers on a scenario where the Carl I. Samson Company (C.I.S. Co) in Maine acquires a firm called "Big-Corp" with branches in ITExamAnswers

The primary objective is to implement a unified network using static routing , and various Layer 2 security Key Case Study Components

The assignment is generally divided into phases that mirror the SRWE course modules: Phase I: IP Addressing and VLANs IPv4 & IPv6 Design

: Subnetting both protocols to accommodate multiple locations. Inter-VLAN Routing

: Implementing router-on-a-stick or SVI-based routing to allow communication between different departmental VLANs. Phase II: Infrastructure Configuration EtherChannel ccna-2v7.0 case study -rev b-

: Configuring link aggregation (LACP) between switches to increase bandwidth and provide redundancy. Spanning Tree (STP)

: Ensuring a loop-free topology while maintaining redundant paths. DHCP Services

: Configuring a router or dedicated server to provide dynamic addressing for hosts. Phase III: Security and Wireless Switch Security : Applying Port Security DHCP Snooping BPDU Guard to mitigate common Layer 2 attacks. Wireless LAN (WLAN)

: Setting up basic wireless access, often using WPA2-PSK for security. SSH Management

: Securing remote access by disabling Telnet and enabling SSH with local user authentication. ITExamAnswers Implementation Checklist Description Initial Settings

Hostnames, passwords (secret, console, vty), and banner MOTD. VLAN Creation Assigning specific IDs and names; assigning access ports.

Configuring 802.1Q trunks and matching native VLANs on both ends. Static Routing

Defining routes to internal networks and a default route to the ISP. Verification commands (e.g., show ip route show ip int brief show etherchannel summary ) to confirm connectivity.

The CCNA-2 v7.0 Case Study -Rev B- is a comprehensive capstone project within the Cisco Networking Academy's Switching, Routing, and Wireless Essentials (SRWE) curriculum. It serves as a practical assessment where students must design, configure, and troubleshoot a multi-site enterprise network that reflects real-world deployment challenges. Objectives of the Case Study

The primary goal of Revision B is to validate your ability to integrate the core technologies introduced in CCNA v7.0. Key objectives include:

VLAN and Trunking Implementation: Segregating traffic for security and performance using 802.1Q trunks.

Redundancy Protocols: Configuring EtherChannel for link aggregation and Spanning Tree Protocol (STP) to prevent loops.

Dynamic Addressing: Setting up DHCPv4 and DHCPv6 (Stateless/Stateful) to automate IP management.

Routing and Security: Implementing Inter-VLAN routing (Router-on-a-Stick or Layer 3 Switching) and securing the infrastructure with SSH and Port Security. Core Configuration Components

The case study typically requires a hands-on approach using Cisco Packet Tracer or physical hardware to meet the following requirements: 1. Layer 2 Redundancy and Switching

Students must ensure high availability by configuring EtherChannel (LACP) between core switches. This allows for increased bandwidth and prevents a single point of failure. Additionally, the STP Bridge Priority must be adjusted to designate specific switches as Root Bridges for different VLANs. 2. Advanced IP Services

A major focus of the Rev B version is DHCP Relay. When the DHCP server is located in a different subnet, students must configure the ip helper-address on the router interfaces to forward local broadcast requests. This ensures that clients in remote branches can still receive dynamic addressing. 3. WLAN Configuration

In line with modern enterprise needs, the study often includes the setup of a Wireless LAN Controller (WLC). This involves: Defining SSIDs with WPA2-PSK or Enterprise authentication. Mapping SSIDs to specific VLANs.

Ensuring seamless connectivity between wired and wireless clients. Troubleshooting and Best Practices

The -Rev B- designation often indicates updated security requirements or revised IP addressing schemes compared to the original version. To succeed, students should follow these Cisco-recommended practices:

Document the Topology: Always maintain an up-to-date IP address table.

Verify Step-by-Step: Use commands like show ip interface brief, show etherchannel summary, and show vlan brief after every major configuration block.

Secure Management: Always disable unused ports and use secret passwords rather than plain-text. Recommended Study Resources

For those preparing for the 200-301 CCNA exam or completing this case study, several platforms provide guided walkthroughs and lab files:

ITExamAnswers: Offers detailed exam answers and lab solutions for SRWE modules.

Pearson: The official CCNA v7 introduction provides the conceptual foundation needed for complex case studies.

Study-CCNA: A high-quality resource for understanding the breadth of the 200-301 curriculum, including wireless and security concepts.

Are there specific Packet Tracer instructions or configuration commands from the Case Study -Rev B- you would like me to explain further?

The CCNA-2v7.0 Case Study (Rev B) requires configuring a multi-site network for the Carl I. Samson Company (C.I.S. Co) following an acquisition, focusing on integrating Bangor, Phoenix, and Chicago locations. The project mandates implementing IPv4/IPv6 addressing, static routing, VLANs, switchport security, and DHCP services across the infrastructure. Detailed project requirements can be found at Course Hero.

Solved CCNA-2v7.0 Case Study (Rev B) Static Routes, VLANs

CCNA 2 v7.0 Case Study - Rev B: A Comprehensive Guide

The Cisco Certified Network Associate (CCNA) certification is a highly respected credential in the IT industry, and the CCNA 2 v7.0 case study is an integral part of the certification process. In this article, we will provide a comprehensive guide to the CCNA 2 v7.0 case study - Rev B, including an overview of the case study, its objectives, and a step-by-step walkthrough of the solution.

What is CCNA 2 v7.0 Case Study - Rev B?

The CCNA 2 v7.0 case study - Rev B is a real-world scenario-based assessment that tests a candidate's skills and knowledge in designing, implementing, and troubleshooting a network. The case study is part of the CCNA 2 v7.0 curriculum, which focuses on switching, routing, and wireless technologies.

The case study - Rev B is a revised version of the original case study, which was updated to reflect the latest network technologies and industry trends. The case study is designed to evaluate a candidate's ability to apply theoretical knowledge to practical scenarios, making it an essential component of the CCNA certification process.

Objectives of CCNA 2 v7.0 Case Study - Rev B

The primary objectives of the CCNA 2 v7.0 case study - Rev B are:

Design a network topology: Candidates are required to design a network topology that meets the requirements of a fictional company.
Configure network devices: Candidates must configure network devices, including switches, routers, and wireless access points.
Troubleshoot network issues: Candidates are presented with network issues and must troubleshoot them to resolve the problems.

Step-by-Step Walkthrough of CCNA 2 v7.0 Case Study - Rev B

The following is a step-by-step walkthrough of the CCNA 2 v7.0 case study - Rev B:

Step 1: Understand the Company Requirements

The case study presents a fictional company, HQ and two branch offices, Branch1 and Branch2. The company requires a network design that connects all three locations, provides Internet access, and supports wireless connectivity. CCNA-2 v7

Step 2: Design the Network Topology

Candidates must design a network topology that meets the company's requirements. The topology should include:

HQ: 2 switches, 1 router, and 1 wireless access point
Branch1: 1 switch, 1 router, and 1 wireless access point
Branch2: 1 switch, 1 router, and 1 wireless access point

Step 3: Configure Network Devices

Candidates must configure the network devices, including:

Switches: Configure VLANs, trunking, and Spanning Tree Protocol (STP)
Routers: Configure routing protocols, including OSPF and EIGRP
Wireless access points: Configure wireless settings, including SSID, channel, and encryption

Step 4: Troubleshoot Network Issues

The case study presents several network issues that candidates must troubleshoot, including:

Connectivity issues between HQ and Branch1
Wireless connectivity issues at Branch2
Routing issues between HQ and Branch2

Solution to CCNA 2 v7.0 Case Study - Rev B

The following is a sample solution to the CCNA 2 v7.0 case study - Rev B:

Network Topology

The network topology is designed as follows:

HQ: 2 switches (SW1 and SW2), 1 router (R1), and 1 wireless access point (AP1)
Branch1: 1 switch (SW3), 1 router (R2), and 1 wireless access point (AP2)
Branch2: 1 switch (SW4), 1 router (R3), and 1 wireless access point (AP3)

Configurations

The configurations for each device are as follows:

Switches:
- SW1 (HQ): Configure VLANs 10, 20, and 30, trunking, and STP
- SW2 (HQ): Configure VLANs 10, 20, and 30, trunking, and STP
- SW3 (Branch1): Configure VLANs 10 and 20
- SW4 (Branch2): Configure VLANs 10 and 30
Routers:
- R1 (HQ): Configure OSPF and EIGRP routing protocols
- R2 (Branch1): Configure OSPF and EIGRP routing protocols
- R3 (Branch2): Configure OSPF and EIGRP routing protocols
Wireless access points:
- AP1 (HQ): Configure SSID, channel, and encryption
- AP2 (Branch1): Configure SSID, channel, and encryption
- AP3 (Branch2): Configure SSID, channel, and encryption

Troubleshooting

The network issues are troubleshooted as follows:

Connectivity issues between HQ and Branch1: Check the routing table on R1 and R2, and verify that the OSPF and EIGRP routing protocols are configured correctly.
Wireless connectivity issues at Branch2: Check the wireless settings on AP3 and verify that the SSID, channel, and encryption are configured correctly.
Routing issues between HQ and Branch2: Check the routing table on R1 and R3, and verify that the OSPF and EIGRP routing protocols are configured correctly.

Conclusion

The CCNA 2 v7.0 case study - Rev B is a comprehensive assessment that tests a candidate's skills and knowledge in designing, implementing, and troubleshooting a network. By following the step-by-step walkthrough and solution provided in this article, candidates can prepare themselves for the case study and achieve success in their CCNA certification journey.

Additional Tips and Recommendations

Practice, practice, practice: The CCNA 2 v7.0 case study - Rev B requires hands-on experience and practice. Candidates should practice configuring and troubleshooting networks using Cisco equipment or simulators.
Understand the exam format: The CCNA 2 v7.0 case study - Rev B is a simulation-based exam. Candidates should understand the exam format and practice using the simulation tools provided by Cisco.
Review the CCNA 2 v7.0 curriculum: The CCNA 2 v7.0 case study - Rev B is based on the CCNA 2 v7.0 curriculum. Candidates should review the curriculum and ensure they understand the concepts and technologies covered.

By following these tips and recommendations, candidates can achieve success in their CCNA 2 v7.0 case study - Rev B and take a significant step towards achieving their CCNA certification.

CCNA-2 v7.0 Case Study -Rev B- a comprehensive practical assessment within the Switching, Routing, and Wireless Essentials (SRWE)

. It simulates a real-world scenario where a company (often identified as the Carl I. Samson Company or C.I.S. Co) has acquired another business with multiple locations, requiring a unified, secure network infrastructure. Core Objectives & Scenario

The assessment focuses on designing and implementing a multi-site network (e.g., Bangor, Phoenix, and Chicago) using static routing IPv4 and IPv6 addressing. Key technical areas covered include: Layer 2 Security & Redundancy:

Configuring VLANs, Trunking, Spanning Tree Protocol (STP), and EtherChannel. IP Services:

Implementing DHCPv4/DHCPv6 and configuring wireless settings for remote or home office segments. Routing Operations:

Establishing connectivity through static and default routes, including floating static routes for redundancy. Network Security:

Hardening devices with SSH, port security, and encrypted passwords. ITExamAnswers Implementation Phases 1. Physical & Basic Configuration

Devices must be properly placed in the equipment rack and connected via appropriate cabling. Hostname & Banners: Assign unique names (e.g., ) and configure "Message of the Day" (MOTD) banners. Management Security:

Disable IP domain lookups, encrypt all plain-text passwords using service password encryption , and set a minimum password length. SSH Access:

Generate RSA keys (1024-bit modulus), configure local user databases, and enable SSH on VTY lines for secure remote management. Course Hero 2. VLANs and Inter-VLAN Routing Segmentation:

Create and name VLANs according to the provided addressing table.

Configure 802.1Q trunks between switches, ensuring the native VLAN matches on both ends (often VLAN 77). Router-on-a-Stick:

Configure sub-interfaces on the central router to act as the default gateway for each VLAN. ITExamAnswers 3. Static Routing & Redundancy IPv4 & IPv6 Static Routes:

Manually define paths between site summaries (e.g., Phoenix and Chicago summaries) using exit interfaces or next-hop addresses. Default Routes:

Configure a "gateway of last resort" (0.0.0.0/0 or ::/0) pointing toward the ISP or Border Router. Floating Static Routes: Create backup paths by assigning a higher administrative distance (e.g., >90 for EIGRP backups) to the static route. 4. Dynamic Addressing (DHCP) Exclusions:

Reserve specific IP ranges (e.g., .1 to .15) for static assignments to ensure they are not handed out by the DHCP server. Pool Configuration:

Create pools with defined network ranges, default gateways, and DNS server addresses. DHCP Relay: ip helper-address

command on SVIs or sub-interfaces to forward DHCP requests to a central server. ITExamAnswers 5. Switch & Wireless Security

The CCNA-2v7.0 Case Study (Rev B), often associated with Packet Tracer activity 14.6.1, is a comprehensive, hands-on lab designed to test practical application of CCNA 2 (Switching, Routing, and Wireless Essentials - SRWE) concepts . It requires learners to implement a secure, multi-site network for the "Carl I. Samson Company" (C.I.S. Co), involving Phoenix, Chicago, and Bangor locations . Core Components & Objectives

Topology: Involves complex routing between multiple geographical locations (Bangor, Chicago, Phoenix) . IP Addressing: Subnetting the 10.10.64.0/21 range .

VLANs & Trunking: Setting up VLANs, Access Ports, and Trunk Ports .

Static Routing: Implementing IPv4 and IPv6 static routes, including potential floating static routes .

Switch Security: Configuring DHCP Snooping, Port Security, and Dynamic ARP Inspection (DAI) . Design and implement a small network Configure network

Wireless: Configuring a Wireless LAN Controller (WLC) and Access Points .

Spanning Tree Protocol (STP): Configuring and optimizing STP for redundancy . Detailed Review CCNA-1 Case-Study-7.0 -.docx - Course Hero

Based on the typical structure of Cisco Networking Academy (NetAcad) coursework, "CCNA 2 v7.0 Case Study - Rev B" usually refers to the "Design and Build a Small Network" cumulative project.

This project often involves a Packet Tracer activity where students must design an IP addressing scheme, configure routers and switches, and implement security policies.

Below is a draft for a professional social media post (suitable for LinkedIn or a study group) sharing this resource, followed by a brief study guide for the concepts involved.

Step 1 – VLAN Creation

On each switch, create VLANs as per case study requirements (e.g., VLAN 10 – Sales, 20 – Eng, 99 – Native).

vlan 10
 name Sales
vlan 20
 name Engineering
vlan 99
 name Native
exit

Layer 3 Verification:

[ ] show ip route – Default route (0.0.0.0/0) exists. Connected routes for all subinterfaces.
[ ] show ip dhcp binding – Clients have received IPs.
[ ] Ping from PC-A to R1’s subinterface → Success.
[ ] Ping from PC-A to PC-B (different VLAN) → Success (via router).
[ ] Ping from PC-B to server (Employee VLAN) → Should fail if ACL is applied correctly.
[ ] Ping from PC-B to 8.8.8.8 (ISP loopback) → Success.

Conclusion

The CCNA-2v7.0 Case Study -Rev B- is not merely a test of rote commands; it is a simulation of a network engineer’s daily workflow. By methodically working through VLAN segmentation, inter-VLAN routing, DHCP, static routing, NAT, and ACLs, you are constructing a small enterprise network from scratch.

Remember the troubleshooting mindset: start at Layer 1, verify Layer 2, and only then proceed to Layer 3 and above. Use ping, traceroute, and show commands relentlessly. If a ping fails, check the ARP table, check the routing table, and verify ACLs.

Mastering this case study will leave you with a portfolio-worthy configuration and the confidence to move on to the third CCNA v7.0 course (ENSA) and, ultimately, the CCNA certification exam. Good luck, and happy configuring.

Next Steps: After completing Rev B, review your configuration against the official scoring rubric. If possible, have a peer review your ACL logic. Then, document every interface IP, VLAN mapping, and route in a network diagram – that documentation is a habit of successful professionals.

The CCNA-2v7.0 Case Study (Rev B) is a comprehensive practical assessment within the Cisco Networking Academy "Switching, Routing, and Wireless Essentials" (SRWE) curriculum. It simulates a real-world merger scenario involving the Carl I. Samson Company (C.I.S. Co), which has expanded its Bangor, Maine headquarters by acquiring "Big-Corp" offices in Phoenix and Chicago.

This case study challenges students to integrate multiple core networking concepts into a single, cohesive infrastructure using both IPv4 and IPv6. Core Objectives and Requirements

The Rev B assessment focuses on several key technological pillars of the SRWE course:

Static Routing: Implementing primary and backup (floating) static routes for both IPv4 and IPv6 to ensure connectivity between geographic sites.

VLANs and Inter-VLAN Routing: Organizing local traffic into segments and configuring "Router-on-a-Stick" or Layer 3 switch SVIs for communication.

Switch Security: Applying best practices like port security, disabling unused ports, and configuring encrypted management access via SSH.

DHCP Services: Configuring routers to act as DHCPv4 and DHCPv6 servers to automate host addressing.

WLAN and Redundancy: Setting up Wireless LANs and ensuring network stability through EtherChannel and Spanning Tree Protocol (STP). Phase-by-Phase Implementation 1. IP Addressing and VLAN Design

In the initial phase, you must develop an addressing scheme based on specific user requirements for each site.

Phoenix (PHX): Typically requires sub-interfacing on the Phoenix router to support multiple VLANs (e.g., VLAN 120).

Chicago (CHG): Often acts as a central hub for specific services like DHCP.

Bangor (BAN): The headquarters router, frequently used to handle IPv6 DHCP pools (e.g., "DHCP-DNS"). 2. Basic Device Configuration

Security is a priority from the start. On all routers and switches (like CHG-RTR, PHX-SW-1, and BAN-RTR), you must:

Secure the IOS: Encrypt all passwords, set a minimum password length (often 10 characters), and disable IP domain lookups.

Management Access: Configure a domain name (e.g., cisco.com), generate 1024-bit RSA keys, and enable SSH version 2 on VTY lines.

Brute-Force Protection: Use commands to block login attempts for a specified period (e.g., 1 minute) after 3 failures in 60 seconds. 3. Advanced Layer 2 and Layer 3 Features

The core of the "Rev B" study involves complex connectivity tasks: Chegghttps://www.chegg.com

Solved CCNA-2v7.0 Case Study (Rev B) Static Routes, VLANs

It looks like you’re looking for a proper guide for the CCNA v7.0 (2.7.0) Case Study – Revision B.

First, a quick clarification:
The official Cisco NetAcad curriculum for CCNA 2 v7.0 (Switching, Routing, and Wireless Essentials) includes several Case Studies depending on the instructor or region — but the most common “Rev B” case study focuses on multi-switch configuration, VLANs, trunking, STP, EtherChannel, and inter-VLAN routing, often using Packet Tracer.

Below is a structured guide to complete the standard CCNA 2 v7.0 Revision B Case Study successfully.

1. Understand the Case Study Objectives

You’ll typically need to:

Design and configure VLANs on multiple switches.
Configure trunking (802.1Q) between switches.
Implement Rapid PVST+ and adjust STP root bridge placement.
Configure EtherChannel for redundancy and increased bandwidth.
Set up a router-on-a-stick or use a multilayer switch for inter-VLAN routing.
Verify connectivity and troubleshoot common issues.

6. Where to Get the Exact Case Study File

Cisco NetAcad instructors can download the official .pka case study from the Instructor Resources → Course Materials → Case Studies in CCNA v7.0.

If you don’t have instructor access, check your course syllabus or ask your instructor for “SRWE Case Study Rev B.”

Scenario

A small company, Clearview Media, has acquired a second office. You are assigned as the network engineer to design, implement, and verify the new branch network and ensure connectivity to the corporate headquarters via a serial WAN link. The network must support three departments (Sales, Engineering, and HR), provide secure access to printers and servers, and allow remote administration from headquarters. The network should be segmented using VLANs, use inter-VLAN routing on a router-on-a-stick, implement OSPF for dynamic routing with HQ, provide NAT for Internet access, secure management via SSH and access lists, and supply DHCP for hosts.

Option 1: Social Media/Forum Share Post

Subject: 📚 Resource Share: CCNA 2 v7.0 Case Study (Rev B) - Design & Build

Body: Looking for the CCNA 2 v7.0 Case Study - Rev B materials? This is the cumulative capstone for the SRWE (Switching, Routing, and Wireless Essentials) curriculum.

It’s a critical exercise for anyone preparing for the new CCNA 200-301 exam. It moves beyond individual chapter labs and forces you to integrate skills like: 🔹 Subnetting and Addressing Schemes. 🔹 VLAN & Trunk configuration. 🔹 Inter-VLAN Routing (Router-on-a-Stick or L3 Switching). 🔹 DHCP & DNS services. 🔹 Security (Port Security, SSH, ACLs).

💡 Study Tip: Don't just look for the answer key! The value in the "Case Study" is the design phase. If you are stuck on the Packet Tracer topology, try building the addressing table manually on paper first.

[Link to resource or file attachment placeholder]

#CCNA #Cisco #NetAcad #Networking #ITTraining #SRWE #CaseStudy

3.5 DHCP Configuration

R1 as DHCP server for VLAN 10:

ip dhcp pool SALES
 network 192.168.10.0 255.255.255.0
 default-router 192.168.10.1
 dns-server 8.8.8.8

Exclude static addresses: ip dhcp excluded-address 192.168.10.1 192.168.10.10