Jungheinrich Etv 216 Error Codes [extra Quality] May 2026
To troubleshoot the Jungheinrich ETV 216 reach truck, follow this guide to understanding its error code system and common faults. How to Read Error Codes
Jungheinrich event messages generally follow a four-digit format (sometimes preceded by a letter like E or F) that breaks down as follows: sd95d2cbd361a0b8d.jimcontent.com First Two Digits
: Categorize the event by function group (e.g., travel, hydraulics, steering). Middle Digits (1-50) : Describe standard events common across all models. Middle Digits (51-99) : Describe model-specific events. Last Digits
: Provide a unique identifier or sub-index for the specific defect. sd95d2cbd361a0b8d.jimcontent.com Common Error Codes & Meanings
If your ETV 216 displays a code, it typically falls into one of these categories: Operator & Safety Errors
These are often caused by the truck's status or operator interaction rather than a mechanical failure. Slideshare : Battery door is open; truck will not operate. : Battery is fully discharged (0%).
: Drive pedal was already pressed when the truck was turned on. : Seat belt is not fastened. : Drive and brake pedals are being pressed simultaneously. Machine Maxx USA System & Hardware Faults
These codes indicate a technical issue with the truck's components. Slideshare Low Voltage (Code 1)
: Often indicates a low battery, blown main fuse, or faulty contactor. Overvoltage (Code 2) : Check the battery voltage or for a faulty controller. Temperature High (Code 3) : Controller exceeds 80 raised to the composed with power 176 raised to the composed with power F). Allow it to cool and check the cooling fans. 10104 / 90104 : Encoder signal issues from the drive or lift motor. jungheinrich etv 216 error codes
: CAN-bus communication error between electronic modules (e.g., traction and lift controllers). Immediate Action Steps When an error appears, the Jungheinrich Service Manual recommends: Jungheinrich Forklift Truck Fault Codes DTC.pdf
Jungheinrich ETV 216 reach trucks use a four-digit event messaging system to communicate operational statuses and mechanical faults. These codes are displayed on the LISA (Logistics Information and Service Display) and help operators and technicians identify whether a problem is a simple operator error or a technical failure requiring professional repair. Understanding Jungheinrich Error Code Structure
Each code is categorized by a "function group" and "event group," typically appearing as a four-digit number (e.g., 1901) or a decimal format (e.g., 1901.1).
Leading Digits (Function Groups): Indicate which system is affected, such as travel (1), hydraulics (2), or steering.
Operator vs. Truck Errors: Codes starting with 0 often refer to operator-related events (like an open door), while others signal hardware issues. Common Jungheinrich ETV 216 Error Codes Operator & Startup Errors
These are often resolved by adjusting how the truck is being used.
1901.1: Drive pedal activated during startup. Ensure your feet are off the pedals when turning on the truck.
1908.1: Seat belt or belt lock not closed. The truck may inhibit travel until the belt is buckled. To troubleshoot the Jungheinrich ETV 216 reach truck,
1909.1: Drive pedal activated while the parking brake is still engaged.
1918.1: Cabin door opened while the truck is ready for operation.
0915.2: Battery door opened. The truck will not operate for safety reasons until the door is secured. Power & Voltage Errors
These codes typically point to issues with the battery, fuses, or the main contactor.
Error 0001 (or E0305.1): Low voltage during system start. Check the battery charge level, the Main Current Fuse, and the main contactor.
Error 0002: Overvoltage. Often caused by an incorrect battery or a faulty controller; travel and hydraulics may be inhibited to prevent damage.
0938.1: Battery fully discharged (0%). Immediate charging is required. Motor & Sensor Faults
These codes often require technical inspection of the wiring and internal components. Jungheinrich Forklift Truck Fault Codes DTC.pdf Step 4: Contactor & Fuse Checks | Fuse
Step 4: Contactor & Fuse Checks
| Fuse location | Function | |---------------|----------| | F1 (under seat / right panel) | Main traction (80A) | | F2 | Hydraulic pump (100A) | | F3 | Logic / Controller (10A) | | F4 | Lights & horn (15A) |
- Contactor failures (K1, K2, K3) often cause E1302, E1205, or “no lift”.
- Test contactor coil resistance: ~50–150Ω.
Category A: Traction System Errors (Driving)
These are among the most critical as they immobilize the truck.
| Code | Description | Common Root Cause | Immediate Action | |------|-------------|--------------------|-------------------| | 174 03 | Traction motor short circuit (phase to ground) | Damaged motor winding, moisture ingress, or faulty power cable | Check insulation resistance on motor windings. Inspect cable harness from inverter to motor. | | 174 05 | Traction motor temperature sensor failure | Open circuit or shorted NTC thermistor | Measure resistance at motor plug (usually 10kΩ at 25°C). Replace sensor or motor. | | 024 10 | Accelerator pedal signal implausible | Pedal sensor (Hall effect) out of range; double sensor mismatch | Clean pedal connector. Use CAN monitor to compare pedal channel 1 vs channel 2 (should be complementary). | | 024 13 | Accelerator pedal return spring check failed | Mechanical spring broken or sensor stuck at >5% when brake applied | Replace complete accelerator pedal module. | | 188 02 | Brake resistor overload | Frequent braking with heavy load or shorted braking chopper | Check brake resistor (ohm value: typically 4–8Ω). Look for cracked housing. Replace if open circuit. |
Understanding the Jungheinrich Diagnostic System
Before examining specific codes, it is crucial to understand how the ETV 216 communicates problems.
-
Display Interface: The ETV 216 typically uses a multifunction LCD display on the control panel.
-
Code Structure: Codes generally appear as a combination of a letter (A, B, C, D, E, F, H, L, S, or U) followed by three or four digits (e.g., B124 or E4513).
- A codes: Steering system faults
- B codes: Braking system faults
- C codes: CAN bus / Communication errors
- D codes: Drive motor or controller faults
- E codes: Lift/Hydraulic system errors
- F codes: Battery or charger malfunctions
- H codes: Overtemperature warnings
- L codes: Lighting / Electrical accessory issues
- S codes: Speed or travel interlock problems
- U codes: User interface or tiller/joystick errors
-
Active vs. Stored Codes: The system retains a history of intermittent faults. A flashing code indicates an active shutdown condition; a steady code is a logged event.
When You Don’t Have a Code (But Something Feels Wrong)
Even without a code, the ETV 216 may show:
- Weak lifting: Clean the hydraulic suction filter (located inside the tank).
- Stiff steering: Check the steering gear oil level (separate small reservoir under the hood).
- Random beeping with no display: Low battery voltage – recharge immediately.