V2000-C RFID Access Control is a standalone single-door security system designed for offices, residential buildings, and secure facilities. It supports up to 1000 users
and multiple entry modes including RFID cards (125KHz), PIN codes, or a combination of both. Sesame Access Co., Ltd. Technical Specifications Specification Power Supply 12VDC ± 10% User Capacity 1000 users Reading Distance 3 – 8 cm (1.18~2.36in) 125KHz EM Standard Unlock Relay Door Open Time Adjustable from 0 to 99 seconds Dimensions 119 x 76 x 21 mm (some models 118 x 118 x 20 mm) Installation and Wiring The unit should be mounted approximately 1.2 meters above the ground and roughly 0.5 meters from the door for optimal accessibility. +12V DC power. Black Wire: GND (Ground). Purple Wires: Doorbell button output. Wiegand Interface:
Supports WG26 for connecting external readers or controllers. www.goldbridgesz.com Programming Guide V2000-c Access Control Manual - Facebook
The V2000-C RFID access control system is a compact, 2,000-user device praised for stable performance, though users often find its programming manual complex. It supports multiple entry modes, including card-only, PIN-only, or card-and-PIN combinations. Detailed information and user experiences with the device can be found on JustAnswer.
The V2000-C RFID access controller is a reliable, low-maintenance unit suitable for small to medium-sized installations. Strict adherence to the wiring diagrams and master code security practices outlined in the manual prevents 90% of operational failures. For advanced features (time zones, anti-passback, or audit trails), refer to the advanced programming appendix or upgrade to the networked V2000-C Pro model.
Appendix (Typical)
End of Report
V2000-C RFID Access Control User Manual: A Comprehensive Guide
The V2000-C RFID Access Control system is a popular, standalone security solution designed for small to medium-sized businesses, residential complexes, and secure storage areas. This guide serves as a comprehensive manual to help you install, program, and maintain your device. 1. Introduction & Specifications
The V2000-C is a single-door multifunction standalone access controller. It supports up to 2,500 users and allows access via RFID card, a 4-to-6 digit PIN, or a combination of both. Operating Voltage: DC 12V ± 10% User Capacity: 2,500 Card Reading Distance: 3–6 cm Active Current: <60mA Lock Output Load: Max 3A Operating Temperature: -45°C ~ 60°C 2. Installation and Wiring
Before mounting, ensure the power is disconnected. The rear of the unit features a color-coded wiring harness. Description Red Positive Power Supply Black Negative Power Supply Blue Normally Open (Electronic Lock) Purple Common Terminal Orange Normally Closed (Magnetic Lock) Yellow Exit Button Input Pink Doorbell Interface 3. Programming Basics
To enter programming mode, you must use the Master Code. The factory default Master Code is 999999.
Enter Programming Mode: Press * + 999999 + #. (The indicator light will turn orange/flashing). Exit Programming Mode: Press *.
Change Master Code: Enter programming mode, then press 0 + [New 6-digit Code] + # + [Repeat New Code] + #. 4. User Management Adding Users (Card or PIN) Enter Programming Mode. Press 1. For Card: Swipe the RFID card.
For PIN: Enter a unique User ID (1-2500) + # + [4-6 digit PIN] + #. Press * to exit. Deleting Users Enter Programming Mode. Press 2. By Card: Swipe the card you wish to delete. By ID: Enter the User ID + #. Press * to exit. 5. Advanced Settings Door Relay Time
To adjust how long the door remains unlocked (0-99 seconds): Enter Programming Mode. Press 4 + [0-99] + #. (Default is 5 seconds). Access Mode Configuration You can choose how users authenticate: Card Only: Press 3 + 0 + # Card OR PIN: Press 3 + 1 + # (Default) Card + PIN: Press 3 + 2 + # 6. Resetting to Factory Defaults
If you forget the Master Code or wish to clear all settings: Power off the device. Press and hold the # key while powering the device back on. V2000-c Rfid Access Control User Manual
Release the key after two beeps. The Master Code is now reset to 999999. 7. Troubleshooting Card not reading: Ensure the card is 125KHz EM frequency.
Constant Beeping: Check for a short circuit in the wiring or an "anti-tamper" alarm trigger.
Keypad not responding: Verify the input voltage is a steady 12V DC.
Security Tip: Always change the default Master Code immediately after installation to prevent unauthorized access to your programming settings.
V2000-C RFID Access Control User Manual: Installation and Programming Guide
The V2000-C RFID Access Control system is a versatile, standalone security solution designed for small to medium-sized businesses, residential complexes, and secure storage areas. This manual provides a step-by-step guide on how to install, wire, and program your device to ensure maximum security. 1. Technical Specifications
Before installation, ensure your environment meets the following requirements: Operating Voltage: DC 12V ±10% User Capacity: 1,000 to 2,500 users (model dependent) Card Reading Distance: 3–6 cm Card Type: ID (EM) card or IC (Mifare) card Output Interface: Wiegand 26 (for external readers) Lock Output Load: Max 3A 2. Installation and Wiring
Mount the unit on a flat surface away from extreme heat or moisture. Follow the wiring diagram below to connect the unit to your power supply and electronic lock. Wiring Terminal Definitions: Red: +12V DC (Power) Black: GND (Ground) White: OPEN (Exit Button) Blue: COM (Relay Common) Yellow: NO (Normally Open – for Fail-Secure locks)
Green: NC (Normally Closed – for Fail-Safe/Magnetic locks) Grey: BELL (Doorbell connection) 3. Programming Guide
To enter programming mode, you must use the Master Code. The default master code is usually 990101 or 123456. Enter/Exit Programming Mode Press * + [Master Code] + #. (The LED will turn red/flash). Press * to exit programming mode at any time. Change the Master Code
It is highly recommended to change the default code immediately.
Enter Programming Mode -> Press 0 + [New 6-digit Code] + # + [Repeat New Code] + #. Adding Users (Card or Keyfob) Enter Programming Mode. Press 1 + [Read Card] + #.
To add multiple cards, read them one after another, then press # to finish. Adding Users (Personal PIN) Enter Programming Mode. Press 1 + [4-digit User ID] + # + [4-digit PIN] + #. Deleting Users
By Card: Enter Programming Mode -> Press 2 + [Read Card] + #.
By User ID: Enter Programming Mode -> Press 2 + [User ID] + #.
Delete All Users: Enter Programming Mode -> Press 2 + 0000 + #. 4. Door Open Modes You can configure how users gain entry: Card Only: Press 3 + 0 + #. Card + PIN: Press 3 + 1 + #. Card or PIN (Default): Press 3 + 2 + #. 5. Setting the Door Delay Time V2000-C RFID Access Control is a standalone single-door
The delay time determines how long the lock remains open after a valid entry. Enter Programming Mode. Press 4 + [00–99 Seconds] + #. Note: 00 sets the relay to toggle mode (latched). 6. Troubleshooting
Forgot Master Code: Power off the device. Press and hold the # key (or the reset button inside the housing) while powering back on. The device will beep, and the Master Code will revert to the factory default.
Card Not Reading: Ensure the card type (EM vs IC) matches the reader frequency and that there is no metal interference behind the mounting surface.
Continuous Beeping: This usually indicates the "Tamper Alarm" has been triggered. Ensure the back cover is securely fastened.
Disclaimer: Security settings should be handled by an authorized technician. Always test the Exit Button and emergency overrides after installation.
The V2000-C is a standalone RFID access control keypad designed for single-door security. It supports up to 1,000 users and utilizes 125KHz EM standard cards. 1. Core Specifications Operating Voltage: 12VDC ± 10%. Unlock Relay: 12VDC / 2A. Card Type: 125KHz EM standard RFID cards. User Capacity: Up to 1,000 users. Entry Modes: Card only, PIN only, or Card + PIN. 2. Setup and Programming
To perform any administrative tasks, you must first enter Programming Mode.
Enter Programming Mode: Press [*] + [6-digit Programming PIN] (Default is often 123456 or 888122). Two beeps confirm entry.
Change Programming PIN: Press [0] + [New 6-digit PIN] + [Repeat New 6-digit PIN].
Exit Programming Mode: Press [*] or wait for the system to time out. 3. User Management
Most standalone units like the V2000-C use numeric commands for management: Add RFID Card: Enter Programming Mode. Press [5] + [4-digit User ID] (e.g., 0001). Present the RFID card to the reader (you will hear a beep). Press [#] to confirm. Delete RFID Card: By Card: Press [7] + [Present Card] + [#]. By User ID: Press [6] + [4-digit User ID] + [#]. Add Public PIN: Press [3] + [4-digit Public PIN] + [#]. 4. System Settings
Door Open Duration: Press [2] + [Time in seconds (00-99)] + [#] (e.g., 05 for 5 seconds). Set Access Mode: Card or PIN (Default): Press [4] + [0] + [#]. Card and PIN: Press [4] + [1] + [#]. 5. Resetting to Factory Defaults
If you lose the master code, you can typically reset the system using an internal jumper. Power off the device.
Move the internal jumper (often labeled JP4 or S16) to pins 1-2. Power the device on and wait for the beeps. Power off again and move the jumper back to pins 2-3.
For further technical support or visual wiring diagrams, refer to the Obohands Download Center or Scribd's Programming Manual.
V2000-C Standalone access controller system for single door access Appendix (Typical)
Introducing the V2000-C RFID Access Control System: A Comprehensive User Manual
Are you looking for a reliable and efficient access control solution for your organization? Look no further than the V2000-C RFID Access Control System. This user manual provides a detailed guide on how to install, configure, and operate the V2000-C system, ensuring that you get the most out of your access control investment.
Overview of the V2000-C System
The V2000-C RFID Access Control System is a cutting-edge solution designed to provide secure and convenient access control for various applications, including office buildings, schools, hospitals, and more. The system utilizes RFID technology to grant authorized individuals access to designated areas, while preventing unauthorized entry.
Key Features of the V2000-C System
Installation and Configuration
The V2000-C system is easy to install and configure, with a user-friendly interface that guides administrators through the process. The system can be integrated with existing security systems, including alarms and CCTV cameras.
Operating the V2000-C System
The V2000-C system is designed to be easy to use, with a simple and intuitive interface that allows administrators to manage access control with ease. The system can be operated using a variety of methods, including:
Troubleshooting and Maintenance
The V2000-C system is designed to be reliable and durable, but like any system, it may require occasional troubleshooting and maintenance. The user manual provides a comprehensive guide on how to troubleshoot common issues and perform routine maintenance tasks.
Conclusion
The V2000-C RFID Access Control System is a powerful and reliable solution for managing access control in various applications. With its user-friendly interface, durable design, and advanced features, the V2000-C system provides a comprehensive access control solution that meets the needs of organizations of all sizes. Download the V2000-C RFID Access Control User Manual today and discover how to get the most out of your access control investment.
Requires X cards (1-9) to be swiped in sequence to open the door.
25 [Number of Cards] #25 3 # (Three different users must swipe; the door opens on the 3rd swipe).Date: [Current Date] Prepared For: Security System Administrators / End Users Subject: Functional Overview, Installation Guidelines, and Operational Procedures