The "Failed to Update" error in Kolimer loaders for VCDS (VAG-COM Diagnostic System) typically happens when the software tries to connect to official servers or when the interface firmware and loader version are mismatched. Because Kolimer is a loader for clone interfaces
, official updates from Ross-Tech will likely block or "brick" your cable. Immediate Troubleshooting Steps Disable Internet and Antivirus
: This is the most common fix. Turn off your Wi-Fi/Ethernet and disable Windows Defender or any third-party antivirus before launching the loader, as they often flag the loader as a false positive or attempt a blocked update. Clean Reinstall of Drivers Device Manager , find the Ross-Tech device, right-click it, and select Uninstall device . Be sure to check the box for " Delete the driver software for this device
Unplug the cable, restart your PC, and then reinstall the VCDS software and drivers provided with your specific loader version. Use the Correct Launch Order Ensure the cable is from the PC during VCDS installation. After installation, copy the VCDSLoader.exe
(Kolimer) into the main Ross-Tech installation folder (usually C:\Ross-Tech\VCDS
launch the software using the loader shortcut, never the original Fixing a "Revoked" or Blocked Cable
If your cable was updated by accident and no longer connects, its internal EEPROM might be "deactivated" or revoked. Reflash the EEPROM : You may need a specific utility like VAGCOM_EEWriteLang.exe
(often found in Loader 9.2 archives) to reflash the cable's internal memory and reset it to a working state. Firmware Downgrade
: Some users find success using a firmware updater included in "Loader 9.2" or similar archives to force the cable back to a compatible version. Critical Precautions Avoid Official Updates
: Never click "Check for Updates" within the VCDS software options if you are using a Kolimer loader; this often leads to the "Interface not found" or "License revoked" error. Windows "S Mode" : If you are on a new laptop, ensure Windows is not in
, which prevents the installation of non-Microsoft Store apps like VCDS.
Did the "Failed to Update" message appear immediately after you connected to Wi-Fi, or did it happen during a firmware flash?
Elevator 10, Driver Installation, No COM Port Created - Elektroda
A failure of the VCDS Loader (Kolimer) often occurs when the loader tries to access a version of VCDS it wasn't built for or when the firmware on a "clone" cable becomes desynced from the software.
To resolve a "Failed to Update" or "Failed" error with the Kolimer loader, follow these specific technical steps: 1. Match Loader and Software Versions
The Kolimer loader is version-specific. If you updated the official VCDS software from Ross-Tech, the older loader will fail to launch it.
Fix: Ensure your VCDS version matches the one supported by your specific loader version (e.g., Loader v9.2 usually supports VCDS 20.4 through 23.x).
Action: Reinstall the exact version of VCDS that came with your interface or find an updated loader (like v9.2 or v10) from specialized automotive forums like MHH Auto or Digital Kaos. 2. Disable Anti-Virus and Windows Defender
The Kolimer loader is often flagged as a "False Positive" because it modifies how VCDS launches to bypass official licensing checks.
Fix: Add the entire VCDS installation folder (usually C:\Ross-Tech\VCDS) and the vcds_loader.exe to your Antivirus Exceptions.
Action: If the loader disappeared or won't open, your antivirus likely quarantined it. Restore the file and disable real-time protection during use. 3. Firmware Resync (VII Config)
If the error occurs after an accidental internet update, the cable's firmware may be locked or "bricked."
Fix: Use the VCI Config Utility (often included in the loader package) to check the interface status. Action: Open the VCI Config tool.
If the firmware shows "Unknown" or "Failed," attempt to re-flash the firmware provided with your clone software package.
Caution: Never use the official Ross-Tech firmware update tool on a clone cable, as this will permanently disable the interface. 4. Internet Block (Firewall) vcds loader kolimer failed 2 updated
Modern VCDS clones are designed to fail if they detect an internet connection.
Fix: Always use the software with your Wi-Fi turned off or create a Firewall Outbound Rule for vcds.exe and vcds_loader.exe. Summary Table: Common Failures Failure Type Loader won't open Error: "File not found" Restore from Antivirus quarantine; add exception. Software won't start "Interface not found"
Disable internet and ensure the cable is plugged into a car's OBDII port (12V power is required). Update loop Loader asks to update VCDS
Do not update. Reinstall the original version provided with your cable.
This error typically occurs when using VCDSLoader (developed by Kolimer) with a "clone" HEX-V2 or HEX-NET interface. The message indicates that the loader has detected an update or a mismatch that prevents it from bypassing the standard Ross-Tech security checks. Because clones are unauthorized copies of
hardware, the official software often attempts to "brick" or disable them if it detects they are not genuine. Common Causes Internet Connection:
If the software was opened while connected to the internet, it may have checked for official updates, which often "kills" the loader's bypass. Version Mismatch:
You might be trying to use a newer version of the VCDS software that is not yet supported by your current version of the Kolimer loader. Driver Corruption:
Windows updates can sometimes overwrite the specific drivers needed for the clone interface to communicate with the loader. Troubleshooting & Fixes Complete Clean Reinstall: Unplug the interface from the laptop and car. Uninstall all versions of VCDS and any existing drivers. Delete the C:\Ross-Tech folder entirely.
Reinstall the specific version of VCDS provided with your cable, followed by the Kolimer Loader Firewall Rules: Create an outbound rule in Windows Firewall VCDSLoader.exe from accessing the internet entirely. Use 32-bit Version:
Some users have found that even on 64-bit systems, installing the 32-bit version of VCDS resolves "failed to update" or connectivity issues. Hardware Recovery:
If the lights on your cable are flashing red or it is no longer recognized as a "Ross-Tech" device in Device Manager, the firmware may be bricked. This sometimes requires "bench flashing" the internal chip (e.g., Atmega162) using external hardware. A word of caution:
Using clone hardware carries the risk of it being permanently disabled by official software updates. For stable performance and full support, many users eventually move to a genuine Ross-Tech interface Are you currently seeing specific flashing lights
on your cable, or is it just the software showing the error?
If your VCDS Loader (Kolimer) is failing to update or causing connection issues, it is often due to the interface getting stuck in a firmware update loop or driver conflicts. This is common with HEX-V2 clones if they are updated through the official Ross-Tech software by mistake. Fixing a Failed VCDS Update Perform a Clean Reinstall
Open Device Manager, find the Ross-Tech device, right-click it, and select Uninstall device. Check the box for "Delete the driver software for this device".
Uninstall the VCDS software and the Kolimer Loader from your computer.
Download and reinstall the VCDS software, but do not open it immediately after installation. Reset the Interface (Hardware Reset)
Unplug the interface from both the computer's USB port and the car's OBD-II port.
If your interface has flashing red lights, it is stuck in update mode.
Plug it back into the PC (do not connect to the car yet). Start the VCIConfig utility (found in the VCDS installation folder) manually.
Go to the Update tab and click Check for updates to force the firmware to re-flash correctly. Manual Installation for Clones (Kolimer Loader)
Disable Antivirus/Windows Defender: These often flag loaders as threats.
Turn off Internet: To prevent the software from checking Ross-Tech servers and potentially "blocking" your cable. The "Failed to Update" error in Kolimer loaders
Copy the VCDSLoader.exe file into the main Ross-Tech installation folder (usually C:\Ross-Tech\VCDS).
Create a desktop shortcut for VCDSLoader.exe and always use this to launch the program instead of the standard VCDS icon. Troubleshooting Common Errors
"Interface Not Found": If you have a 64-bit laptop, try reinstalling the 32-bit drivers during the VCDS setup, as some clone interfaces require the 32-bit stack to communicate properly.
License Revoked: If your license appears revoked after an update, you may need a specific firmware repair tool (like "Loader 9.2" or similar) to re-flash the internal EEPROM.
Windows "S Mode": Ensure your laptop is not in Windows S Mode, which prevents the installation of non-Microsoft Store apps like VCDS.
Are you seeing specific colored flashing lights on your cable, or is there a particular error code appearing on your screen?
Hex V2 Clone - Licence revoked - Help please? : r/CarHacking
Comments Section * _ne555_ • 4mo ago. If you say "Hex V2" vlone, I assume it's one of those old clones that is actually a Hex (V1) Reddit·r/CarHacking
The error message "vcds loader kolimer failed 2 updated" typically indicates that the Kolimer loader (a third-party tool used for unofficial VCDS interfaces) is unable to verify or download its required update files from its server. Why the Update Fails
Server Offline: The most common reason is that the remote server hosted by Kolimer is down or no longer maintained.
Security Interference: Windows Defender or other antivirus software may have flagged the loader as a threat and blocked its connection or deleted a necessary .dll file.
Firewall Blocking: Your system's firewall might be preventing the loader from communicating with its update server. Troubleshooting & Fixes
If you are facing this issue, follow these steps to restore functionality: Disable Antivirus/Security:
Temporarily disable Windows Defender and any third-party antivirus software.
Check your "Quarantine" folder; if the loader was flagged, restore the file and add the entire VCDS folder as an exclusion in your antivirus settings. Run as Administrator:
Right-click the VCDSLoader.exe and select Run as Administrator to ensure it has the necessary permissions to update or write files. Manual Update/Reinstallation:
Since the built-in update often fails, you may need to manually download the latest version of the loader (e.g., version 9.2 or newer) from a reputable forum or provider.
Ensure the loader version matches the VCDS software version you are trying to run. Internet Connection:
Verify your internet is active, but note that some users recommend disabling the internet after the initial setup to prevent the official VCDS software from "deactivating" an unofficial cable. Interface Firmware Check:
If the loader opens but cannot see the cable, you may need to re-run the "Test" in the Options menu while the cable is plugged into both the laptop and the car (with the ignition ON). Important Safety Note
Unofficial loaders like Kolimer are not supported by the official developer, Ross-Tech. If your cable is "revoked" or bricked during an update, it may require a hardware reflash using tools like an Atmega162 programmer.
VCDS Loader Kolimer Failed 2: What Does it Mean and How to Fix It?
If you're a Volkswagen or Audi owner, you're likely familiar with the VCDS (Vag-Com Diagnostic System) tool, which allows you to diagnose and modify various settings on your vehicle. However, some users have reported encountering an error message while using the VCDS loader, specifically "Kolimer failed 2." In this article, we'll explore what this error means, its causes, and most importantly, provide step-by-step solutions to fix it.
What is VCDS Loader Kolimer Failed 2?
The VCDS loader is a crucial component of the VCDS system, responsible for loading the necessary drivers and settings to communicate with your vehicle's ECU (Engine Control Unit). The "Kolimer failed 2" error typically occurs when the VCDS loader fails to initialize or connect to the ECU, preventing the tool from functioning correctly.
The error message "Kolimer failed 2" is often accompanied by other symptoms, such as:
Causes of VCDS Loader Kolimer Failed 2
Several factors can contribute to the "Kolimer failed 2" error. Some common causes include:
Updated Solutions for VCDS Loader Kolimer Failed 2
To resolve the "Kolimer failed 2" error, try the following step-by-step solutions:
Solution 1: Update VCDS Software
Solution 2: Check and Correct ECU Settings
Solution 3: Troubleshoot Communication Issues
Solution 4: Disable Conflicting Software
Solution 5: Perform a Clean Installation of VCDS
Conclusion
The error "VCDS Loader Kolimer Failed to Update" usually occurs when using third-party loader software for cloned VCDS interfaces. This happens because the loader cannot reach the update server, the interface firmware version doesn't match the software, or security software is blocking the process. Common Fixes
Disable Antivirus/Firewall: These loaders are often flagged as "false positives" by security software. Try temporarily disabling real-time protection and the firewall on your PC, then run the loader as an administrator.
Use the Seller's Software: If you downloaded VCDS directly from the official Ross-Tech website, it will likely fail or even brick (deactivate) your cable if it is a clone. Always use the specific software version provided by the cable's seller.
Re-Flash the Firmware: If the cable has been deactivated, you may need a firmware updater (such as "Loader 9.2") to re-flash the EEPROM and reset the cable's state. Clean Reinstall:
Go to Device Manager, find the Ross-Tech device, and select Uninstall device (check "Delete driver software"). Uninstall all VCDS and loader software from your PC.
Restart your computer and reinstall only the software version compatible with your specific cable.
Check Windows Mode: Ensure Windows is not running in "S mode," which prevents the installation of non-Microsoft Store apps like VCDS loaders.
Warning: Updating a cloned interface with official firmware or software often results in a permanent "License Revoked" error or a "bricked" cable.
Hex V2 Clone - Licence revoked - Help please? : r/CarHacking
Comments Section * _ne555_ • 5mo ago. If you say "Hex V2" vlone, I assume it's one of those old clones that is actually a Hex (V1) Reddit·r/CarHacking
Hey! I purchased a VCDS tester (HEX-V2) clone ... - Facebook
"Loader" tools often attempt to write to protected system folders (System32 or Program Files) or modify registry keys to bypass licensing. The VCDS tool failing to connect to the
Some clones with outdated firmware trigger this error.
Fix:
Kolimer often writes temporary keys to the Windows Registry. If you are not running the loader as Administrator, or if your user account lacks permissions to the HKLM\SOFTWARE\Ross-Tech key, the loader cannot complete its patch sequence.