Xprinter Xp-58iiht Driver !full! May 2026

When you say you need a "paper" on the Xprinter XP-58IIHT driver , it's a bit ambiguous. You might be looking for: A Guide/Instructional Paper:

A document or manual explaining how to download, install, and configure the driver. Physical Paper Specs:

Information on what kind of thermal paper rolls this specific printer uses. Academic/Technical Paper:

A formal report on the driver’s architecture or performance (though these are rare for specific hardware models).

I’ve provided the most likely answers below for the first two categories. 1. Installation & Setup Guide (The "How-To")

is a 58mm thermal receipt printer. To get it running, follow these steps: Driver Download: You can typically find the official drivers on the Xprinter Support Page or through third-party POS support sites like Installation: Connect the printer via and turn it on. Run the driver file as an Administrator. as the printer series during the setup wizard. Choose the correct port (usually or similar). Configuration: xprinter xp-58iiht driver

After installing, go to "Printer Properties" in Windows to set your default paper size to 58mm to avoid cut-off text. 2. Paper Specifications

If you are looking for the physical paper requirements for this printer: Paper Type: Thermal Paper (Direct Thermal, no ink needed). 58mm (approx. 2.28 inches). Roll Diameter:

Usually up to 50mm or 60mm depending on the specific casing. Common Sizes: 57mm x 30mm or 57mm x 40mm are standard. Xiandai Paper Production 3. Troubleshooting Quick Tips Self-Test:

To check if the driver is the problem or if it’s the hardware, perform a self-test by holding the FEED button while switching the power . It should print a configuration page. Blank Prints:

If the printer runs but the paper is blank, ensure the thermal side of the paper is facing the print head (it only prints on one side). 27 Jun 2023 — When you say you need a "paper" on

Here is the content regarding the Xprinter XP-58IIHT driver, structured for a support page, blog, or knowledge base.

4. The "IIH" vs. "IIHT" Compatibility Dilemma

A common source of technical support tickets involves the confusion between the XP-58IIH and the XP-58IIHT.

Compatibility: In 90% of cases, the XP-58IIH driver works perfectly on the XP-58IIHT hardware.
The Failure Case: The IIHT hardware revision introduced slight changes in the DIP switch settings and baud rate handling. If a user forces the IIH driver on an IIHT unit via Serial/Ethernet, they may experience:
- Cut errors (Partial cuts instead of full cuts).
- Paper feed issues (Feeding 10 lines after print).
- Chinese characters appearing in place of English characters (Encoding mismatch).

Recommendation: Always attempt to source the specific "XP-58IIHT" driver first. If unavailable, the generic "Xprinter XP-58" driver found in Windows Update is a safer fallback than the specific IIH driver.

File Naming Convention:

Look for files named like:

XP-58IIHT_Driver_Win10_x64
Xprinter_58IIHT_Setup_v5.2
POS_58IIHT_Network_Driver

Avoid files named simply setup.exe from unknown sources. Compatibility: In 90% of cases, the XP-58IIH driver

Check installation:

Go to Control Panel → Devices and Printers
Look for XP-58IIHT (may show as "XPrinter 58")
Right-click → Printer properties → Print a test page

3.2. Linux Environment

Xprinter does not officially support Linux with proprietary drivers. However, the printer is highly compatible due to its ESC/POS standard adherence.

USB Mode: The printer usually identifies as a USB printer class device.
Driver Solution: The printer-driver-escpos package is the standard solution.
Raw Device Access: Linux treats the printer as a raw device (e.g., /dev/usb/lp0). Developers often bypass the "driver" entirely and write raw ESC/POS commands directly to this device node using Python or C++.

Method 2: Generic ESC/POS Driver (If Official Driver Fails)

If no official driver exists, add the printer as "Generic ESC/POS Printer" but note that cash drawer and cutter may not work.

Linux (CUPS)

The printer uses the EPSON TM-T20 driver or generic ESC/POS driver.
Install via CUPS: sudo apt install cups → open localhost:631 → Add Printer → Select "Raw" or "Zjiang/ESC-POS" driver.

6. Linux installation

Install escpos drivers for CUPS:

sudo apt update
sudo apt install printer-driver-escpos

Then:

Connect USB printer.
Open Printers → Add Printer.
Choose ESC/POS 58mm driver.
Set paper size: 58mm × continuous.

Test:

echo -e "Hello\nLine 2\n\n\n" | lp -d XP58IIHT